Pages

Wednesday, July 29, 2026

You're on My Mind

 When you go to make this car on your own, you start with two 6" x 6" coordinating pieces of DSP (or Vellum in this case).  Place a mark 1 1/2" down from all four corners.  Then cut across to the opposite sides "diagonally" from your marks so that you end up with 4 pieces (all the same) Use one piece from each of the 2 different DSPs to create your personal cards and use whatever sentiment you would like.  I created one for an anniversary card and I changed the orientation of my card.

 YOU’RE ON MY MIND

Cased Eva Dietz




HOW TO CREATE & ASSEMBLE:  

  1. Adhere the two pieces of vellum to one of the (4” x 5 1/4”) white pieces of cardstock as shown
  2. Cut the pieces of linen thread to line along the edges of the vellum using liquid glue Set aside
  3. On a small piece of white cardstock, stamp the sentiment for your card front then die cut it out. 
  4. With the same die, die cut out a piece of Fresh Freesia. Cut it in half lengthwise and adhere it to the sentiment piece as on my card creating a “matted” look.  Adhere this to the card front using Stampin’ Dimensionals®.  Adhere a linen bow to it. 
  5. Die cut out to leaf stems and adhere to the card front.
  6. Embellish the card front with a couple of sequin.
  7. Stamp sentiment and design on the other piece of white cardstock and adhere to the inside of the card.
  8. Stamp the design on the envelope 


WHAT YOU’LL NEED:

Wednesday, July 22, 2026

Sectioned Thank you card


Obviously, when you create this card you can use the Designer Series Paper of your choice along with coordinating color cardstock of your choice. You can embellish with a ribbon or add some gems, This is a simple template that you can use over and over again for any occasion.

 SECTIONED THANK YOU

CASED STAMP4JOY



HOW TO CREATE & ASSEMBLE:

  1. Already done for you cut your DSP into the following sizes: 

Left Side

  • 2-1/2 x 3-1/4
  • 2-1/2 x 1-7/8

Right Side

  • 1-3/8 x 1-1/2
  • 1-3/8 x 2-1/8
  • 1-3/8 x 1-3/8


  1.  Adhere the pieces of DSP  with Multipurpose Liquid Glue leaving approximately and 1/8” around all pieces.
  2. On the piece of Navy cardstock, stamp your sentiment using Versamark.  Then cover in White embossing powder and finish using the heat tool to set it.  Die cut it out.
  3. On the white piece of cardstock, stamp your sentiment with Night of Navy ink .  Adhere the 1/2” strip of DSP along the bottom edge of the white  cardstock.  Adhere this to the inside of your card.
  4. Adhere the additional pice of DSP to your envelope flap and trim off the excess.

WHAT YOU’LL NEED: 


Wednesday, July 15, 2026

CUTEST CREW BIRTHDAY CARD

 CUTEST CREW BIRTHDAY CARD

HOW TO CREATE & ASSEMBLE:

  1. Adhere the DSP to the front of your card base which you have folded on the score line and burnished. Set aside.
  2. On your strip of white cardstock, stamp the dogs ( or cats if you would prefer) and color in with Stampin’ Blends.  Die cut out and set aside.
  3. Run the piece of Misty cardstock through the die cut machine with the textured note die.  Set aside.
  4. Run the (2) strips of espresso cardstock through the die cut machine with the paw prints.  Adhere one to the strip of pecan cardstock.
  5. On the small piece of vanilla cardstock, stamp the sentiment and die cut it out. 
  6. Assemble the front scene of your card.  Use Mini Stampin’ Dimensionals® to pop up the animals and when your scene is done, adhere it to the card front with Stampin Dimensionals®
  7. For the inside, stamp your sentiment on the vanilla piece of cardstock and adhere the other strip of die cut paw prints on the left side of this.  Adhere it into the card.
  8. Stamp the animals on the flap of your envelope and color them in.

WHAT YOU’LL NEED: ( You'll also need Stampin' Blends for coloring> Specific colors not listed here)

Begonia Belle FunFold

Be sure to check out the Sale going on through the month of August on select Designer Series Papers and cardstocks while supplies last. (15...